网站服务器集群构建之：Real Server篇

lvs dr Disable ARPforVIP
1.Using arp_tables_jf to disable ARP
arptables -F
arptables -AIN -d $VIP -j DROP
arptables -AOUT -s$VIP -j mangle --mangle-ip-s$RIP
2.Using arp announce/arp ignore to disable ARP
arp_announce - INTEGER
Define different restriction levelsforannouncing the local
source IPaddressfrom IP packets in ARP requests sent on
interface:
0 -(default)Use any localaddress,configured on any interface
1 - Try to avoid local addresses that are not in thetarget's
subnet for this interface. This mode is useful when target
hosts reachable via this interface require the source IP
address in ARP requests to be part of their logical network
configured on the receiving interface. When we generate the
request we will check all our subnets that include the
target IP and will preserve the source address if it is from
such subnet. If there is no such subnet we select source
address according to the rules for level 2.
2 - Always use the best local address for this target.
In this mode we ignore the source address in the IP packet
and try to select local address that we prefer for talks with
the target host. Such local address is selected by looking
for primary IP addresses on all our subnets on the outgoing
interface that include the target IP address. If no suitable
local address is found we select the first local address
we have on the outgoing interface or on all other interfaces,
with the hope we will receive reply for our request and
even sometimes no matter the source IP address we announce.
The max value from conf/{all,interface}/arp_announce is used.
Increasing the restriction level gives more chance for
receiving answer from the resolved target while decreasing
the level announces more valid sender'sinformation.
arp_ignore - INTEGER
Define different modesforsending replies in response to
received ARP requests that resolve localtargetIP addresses:
0 -(default):replyforany localtargetIPaddress,configured
on any interface
1 - reply only if thetargetIPaddressis localaddress
configured on the incoming interface
2 - reply only if thetargetIPaddressis localaddress
configured on the incoming interface and both with the
sender's IP address are part from same subnet on this interface
3 - do not reply for local addresses configured with scope host,
only resolutions for global and link addresses are replied
4-7 - reserved
8 - do not reply for all local addresses
The max value from conf/{all,interface}/arp_ignore is used
when ARP request is received on the {interface}
net.ipv4.conf.eth0.arp_ignore = 1
net.ipv4.conf.eth0.arp_announce = 2
3. Using the hidden interface to disable ARP
Linux kernel 2.4 and 2.6, you need to apply the hidden patch
# Start the hiding interface functionality
echo 1 > /proc/sys/net/ipv4/conf/all/hidden
# Hide all addresses for this interface
echo 1 > /proc/sys/net/ipv4/conf/ /hidden
# Insert the ipip module
insmod ipip
# Make the tunl0 device up
ifconfig tunl0 up
# Start the hiding interface functionality
echo 1 > /proc/sys/net/ipv4/conf/all/hidden
# Hide all addresses for this tunnel device
echo 1 > /proc/sys/net/ipv4/conf/tunl0/hidden
# Configure a VIP on an alias of tunnel device
ifconfig tunl0:0 up
4. Using redirect to disable ARP
iptables -t nat -A PREROUTING -p tcp -d --dport -j REDIRECT --to-port
5. Using policy routing to disable ARP
# Block access from the LAN to the real server' sVIP.By
# this way we ignore the router's ARP probes. The drawback:
# we ignore the client'sprobes too.We have to do this
# because the client on the LAN can receive replies from all
# real servers
ip rule add prio 99 from 172.26.20/24table99
ip route addtable99 blackhole 172.26.20.118
# Nowacceptlocally any other traffic,i.e.not from
# 172.26.20/24
ip rule add prio 100table100
ip route addtable100 local 172.26.20.118 dev lo
6.Using the noarp module to disable ARP
http://www.masarlabs.com/noarp/
noarpctl add VIP RIP